Search results

  1. IHC Power

    Who has the biggest/loudest setup here?

    Stacks I got a 4 inch exhaust from the turbocharger to a grand rock 5 inch y-pipe feeding two 5 inch ausie stacks set @ 45 degrees away from the cab. Forget my radio i would rather hear my pipes!! Lol
  2. IHC Power

    wiring a streamlight flash light charger

    Streamlight flash light... I got one in my 2001, wired directly to the battery with a 20a inline fuse and groud to chassis. They have smart technology and cannot overcharge the light or the spare battery. So the only draw is the led's on the charger, nothing but milli amps. Wish i had a picture...
  3. IHC Power

    wiring help

    Wiring? You should use 12-14 awg for the harness and the 30a switch on the upfitters. That would be the right thing to do. Good luck and keep trucking.
  4. IHC Power

    changing fan blade question

    Viscous fan Hey man that's a sweet rig you got there, just ordered the same lift kit for my 01 350 psd. Just so you know the tool kit for the fan is not necassary if you have an arm hammer, the water pump threads are reversed(remember that) the radaitor shroud is two pieces when you take the...
  5. IHC Power

    HPOP line o-ring replacement

    Hpop leak, lines? Hey man, before you replace anything get that powerstroke nice and clean, leave it running and pressure wash the intake valley and surrounding area. Ford did put out a service bulletin for the o-rings on the hpop fittings that connect to the lines and there is also a ferry...
  6. IHC Power

    Help Needed not charging, no dash except for battery and abs light

    Charging issue Do yourself a favor and pull the alternator to have it tested first before you exchange it. Make sure it's on the machine correctly like wired in your truck. If it tests good and the batteries are new, all connectors are ok then you should check all the fuses then get a wiring...
  7. IHC Power

    Shimming the FPR Wiki

    No pictures try difuser Yes there are not any pictures there and i am doing the mod tomorrow, the detailed instructions and photos you can find at difuser diesel and they are clear and consise, good luck and keep trucking.
  8. IHC Power

    FYI T444e engine manual

    [b]attention all psd owners, anyone from the forum is welcome to the engine manual i have for 1999-2003 t444e 7.3l engine. It has all engine specs, runout, journal sizes, torque specs, repair sequences, oversize #'s, you name it it's in there. Issued by navistar truck and engine corperation...
  9. IHC Power

    Question Lift kits (tough country)

    So my lift kit is next just wondering what all you guys are running? I'm going for a 6" kit from suspension connection with new front springs, track bar bracket, drop pitman arm, and rear blocks with add a leaf, etc. Going with dual shock set-ups all the way around along with the dual front...
  10. IHC Power

    note Modifications

    Thanks to all you guys for the great ideas for psd's. Just got a chance to get back on here and post, been busy. So the exhaust is done, grand rock turbo back 4", dual 5" ausie stacks sounds great. Did the zoodad mod with bama's idea,thanks man! Cost me $18.00 from lowes. Looks good and sounds...
  11. IHC Power

    7.3 Starting Issue

    I hear ya man I had the same problem on my 2001 350 psd. When i was working at international trucks in boston i got a really god deal on a pack of glow plugs and the relay, try to stay away from the dealer if possible cause the manufacture of the glow plugs for ford is the same the local parts...
  12. IHC Power

    Question Gauges ??

    I really want a set of gauges for my 2001 350. I'm not going to modify the truck much except for my 4 inch exhaust and 5 inch stacks but as a mechanic I really want to monitor my engines vitals, ie, boost, trans temp, and exhaust gas temp. Does anyone know of a fairly priced three gauge A-pillar...
  13. IHC Power

    Fuel tank filler neck (broken)

    Filler Neck repaired Hey all thanks for the advice about the filler neck. I just got through stuffing my fat ass up in between my bedside and frame rail to remove all the crap from the bedside and clean it with acetone. I found some JB Weld kicking around and decided to use that. It's all set...
  14. IHC Power

    injector ?????

    Bad idea Hey man just got in and saw your thread, from my experience working at Ford and International I would say that your going to regret popping one of those injectors in your truck, If you have seen an exposed injector you will see a part number and a serial number but the most important...
  15. IHC Power

    Finally Getting Tranny Rebuilt!

    Still acting up after return from dealer. :stir You got all the o-rings replaced on the injectors, valve cover gaskets which are the wiring harnesses and a reflash along with the transmission rebuild. I have seen more than once the High Pressure Oil Pumps go bad after the injector o-rings...
  16. IHC Power

    5 Speed conversion?

    My 01 Superduty is getting pretty boring with the automatic transmission, plus I am too. Never heard of a conversion but I do have access to a new 5 speed transmission and flywheel, probably have to get the ECM flashed too, otherthan that I'm almost positive that the truck has all the mounting...
  17. IHC Power

    Fuel tank filler neck (broken)

    Wondering if any of you have had this issue, my 2001 350 which is my pride and joy has had a rattle for the past 12 hours over bumps, I located the problem to the filler neck bucket that looks like the previous owner tried to silicone back onto the inside of the bedside. So I pulled the assembly...
  18. IHC Power

    Help Needed Help, runs real bad....then good....then bad

    help? You should probably check the cam sensor, they recalled alot of them, black sensor, gold bracket is the old faulty sensor and the new one is grey with a silver bracket, it's located to the top left of the harmonic balancer. you might even have an injection control pressure issue, you...
  19. IHC Power

    Question Diesel techs:

    White smoke Hello, i'm new to this forum but just wanted to tell you that the six liter powerstroke are known for egr coolers and that is a possible source of the white smoke, diesel's over fueled produce back smoke and the white could possibly be low cylinder temps, but if your a vt365...
  20. IHC Power

    Racing Event Fun ford weekend @ epping nh.

    Ford and ford only, for all you northeastern truck guys and gals, date is august 15th and 16th i've been going to this event for 6 years now and have ran my diesel for the past 2 i've owned it, what a blast. Hope to see you there!!
  21. IHC Power

    Ford recall 1.8M trucks and SUV - 7.3L CPS!! **Main Discussion thread**

    Cam position sensor Hey i just joined this forum so we'll see, don't know if you have been told this yet but the black sensor with the gold bracket is the wrong one! Ford motor company has dropped the price from $110 to just $20 for the newer sensor which is grey with a silver bracket, hope you...
  22. IHC Power

    Hello everyone

    What's going on everyone, just found this forum and figured I would join, never done this stuff before but since we all own the best trucks ever manufactured in the states we obviously have things in common right? I'm a diesel mechanic, I worked for Ford and International so I am very familair...
View older results

Members online

Total: 215 (members: 1, guests: 214)

Forum statistics

Threads
30,547
Messages
266,142
Members
14,676
Latest member
FlorWhitfe

Latest posts

Top