Search results

  1. M

    voltage regulator

    I have a 2001 f250 7.3 PSD If Im reading my manual right it says the voltage regulator is internal to the alternator but auto zone has one listed for my year and model. So are they replacable? And how would i test it? Any body have a wiring diagram?
  2. M

    No power to brake controller

    I have a 2001 f250 superduty with 7.3 diesel. I'm trying to wire a trailer brake controller. I have power from the brake but none from the battery. I just bought the relays that go under the hood what else could i be missing maybe a fuse or something?
  3. M

    Free spin kit installation

    I'm still getting around 15 MPG about the same as before
  4. M

    Free spin kit installation

    The Warn hubs that come with the kit install just like any manual hub with one exception. It uses a spiral lock snap ring on the stub shaft. If you use the standard snap ring with the holes on the end it will stay locked because the ring interferes with the main body clutch gear. Wheel on
  5. M

    Free spin kit installation

    There are 2 different types of wheel studs. Course and fine. The kit should come with both. Once you verify what you have press the new studs into the new hub. Youcan now install the new spindle and ABS sensor. Next pack the bearings in the hub and install. You need a 6...
  6. M

    Free spin kit installation

    here is the new stub shaft This can go on the inner axle shaft with new Ujionts at this time. The studs need to be pulled from the stock unit bearing. And installed in the new spindle
  7. M

    Free spin kit installation

    Theres 4 bolts that hold the unit bearing on. Remove these. THey are on the back of knuckle. Once I got them removed i used two hammers to tap it loose and a paint scraper to get behind it. Use plenty of pb blaster. Once you get the unit bearing off the axle shaft needs to come out. ITs...
  8. M

    Free spin kit installation

    My units bearings went out so instead of replacing them I used the dynatrac freespin kit. Heres some pictures of how it went. First Remove the stock hub locout. Theres a snapring thats pretty easy to take off with pliers. Once you get the snap ring out pull the hub out. When you get...
  9. M

    newbie question

    What is the ID of the axle tube on a dana 50 2001 fordf250?
  10. M

    Tooling for front end work

    I'm finishing up my free spin kit and i did the ball jionts. I'll be doing a write up with pictures in a couple of days if you want to see exactly whats involved.
  11. M

    2001 ford SD axle shaft

    I pulled the snap ring and struggled 2 hrs with that:rant What seal do i need to pull? I removed the hub, snapring 3 washers and washer with groove cut into the back for vaccuum. I still have some seals around the back of the stub shaft behind the knuckle. Do I need to pull those first? How do...
  12. M

    2001 ford SD axle shaft

    I should be able to pull the axle shaft out at this point right?:dunno By using pry bars on the wheel joint. It seems like these seals on the back of the knuckle are holding me up. Are theyt supposed to come throught the knuckle with the shaft or am I missing something that needs to...
  13. M

    Hi

    My name is Kevin. I,ve had a 2001 f250 for about 3 years now. I'm getting ready to make my first mod. The factory sealed bearings went out on me so I'm going to try the dynayrac free spin kit. I post up some pictures after I'm done. I do have a newbie question. I need to get a inner axle seal...

Members online

Total: 503 (members: 2, guests: 501)

Forum statistics

Threads
30,545
Messages
266,136
Members
14,673
Latest member
Doms350

Latest posts

Top