Search results

  1. csarver

    Question Clutch Pedal issue

    I have a 2000 7.3 liter. the other day my clutch pedal went to the floor, the cause was a broken retainer clip that holds the push rod to the pedal arm. I replaced the clip and the clutch went back up but now the pedal is a good 6" higher than it used to be. It is clearly looser at the top...
  2. csarver

    Question 2000 7.3 fuel system issue

    10-4, Ill check for leaks and pressure this weekend. any idea what the proper pressure should be? Chad
  3. csarver

    Question 2000 7.3 fuel system issue

    Yes sir. I drove it 60 miles and am still having the same issue. :dunno
  4. csarver

    Question 2000 7.3 fuel system issue

    Thanks fellas. This is definetly the issue. Ive taken the truck out a couple more times now and sure enough, it will not start until I depressurize the fuel system. Then it starts immediately. If anyone has any info on how to check for air in the line and fix this issue if it is found that...
  5. csarver

    Question 2000 7.3 fuel system issue

    I have a 2000 7.3 liter and it was not starting. I changed the fuel filter (of course I had to depressurize the fuel system when I did this) and the truck started right up. I drove it, shut it off and it wouldnt start again. I popped the hood, depressurized the fuel system and it fired right...
  6. csarver

    Hey Bling821, do you have any idea where Im supposed to go to start a new thread on this...

    Hey Bling821, do you have any idea where Im supposed to go to start a new thread on this website? Chad
    • csarver
    • Profile post
  7. csarver

    Will 2010-2011 F350 rims fit on a 2000 F350?

    Will 2010-2011 F350 rims fit on a 2000 F350?
    • csarver
    • Profile post
  8. csarver

    Parking brake adjustment???

    The only camera I have is on my phone and it is crapped out. I wouldve had them to put up otherwise. Sorry fellas.
  9. csarver

    Parking brake adjustment???

    i finally got it. After I dismantled the entire passenger side drum and removed the drum pads (putting them back on was fun with all the springs and clips) I found what was obviously the star wheel for adjustment. I left the pads on the drivers side and removed the drum to adjust this side...
  10. csarver

    Parking brake adjustment???

    OK, I took the wheel off and found that that when I engage the parking brake, I could not turn the rotor by hand, so it is still working to some extnet, then took the rotor off. (I had no idea that there was a pad under there). After 260,000 miles the pad is completely gone. I still cant find...
  11. csarver

    Parking brake adjustment???

    I have a 2000 F350 4x4 with a manual transmission. My parking brake goes to the floor with no effort and does not hold the truck even on a slight incline. I have looked all along the e-brake cable and found no point of adjustment. I pulled the right rear wheel off and still do not see any...
  12. csarver

    Where do I go to post a new thread? I can never find it when Im looking for it. Can anyone help...

    Where do I go to post a new thread? I can never find it when Im looking for it. Can anyone help the website ignorant???
    • csarver
    • Profile post
  13. csarver

    Question AC Blower issue (I think)

    that was nverknow who was talking about the AC mod. Not sure what he was refering to. Maybe changing an older unit over to run newer coolant???
  14. csarver

    Question AC Blower issue (I think)

    Stroked 68, the only resistor I was able to find on my 2000 was directly behind the round AC blower knob. You have to remove a good portion of the dash to get to it but if you pull the knob off you will have a silver shaft sticking out of the dash. That shaft is part of the resistor box. It...
  15. csarver

    Cab lights installed!

    Yes sir it did. I was looking at the right connector I just ended up with the wrong harness end. buuuuut its all fixed up now. I thought to myself, WWOMD, what would my old man do? I thought back to when I was a 16 year old kid trying to keep my Mustang running and thought, how would my Dad...
  16. csarver

    Cab lights installed!

    I checked at Discount Auto and he said I would have to go to Ford for the connector (I will check Auto Zone tomorrow) I also contacted the guy who sold me the lights and harness. He is telling me that I am looking at the wrong connector under the glove compartment. I have removed the...
  17. csarver

    Cab lights installed!

    Got the lights installed, no problem. The factory wiring harness worked perfectly. The retaining clips were exactly lined up with the holes in the factory roof supports. I used a graduated bit (as you guys reccomended) for the 7/8" hole in the center and a 1/4" bit for the two screws. Everything...
  18. csarver

    Cab lights installed!

    Reference the question on the wiring harness. I got my lights on Ebay for $109. I made sure I got the OEM lights from Ford and I made sure that it came with the harness. The lights have a receiver on the bottom of them and you need the factory harness to click into place. I have my blue tape...
  19. csarver

    Cab lights installed!

    Thanks for the info guys. I thought about the step up bit. I think Ill pick one up and try to install this weekend. (man I hope I dont get any leaks, my buddy with the Duramax will never let me live it down if it starts leaking). Ill let you guys know how it turns out.
  20. csarver

    Cab lights installed!

    I just got my cab lights delivered. I was going to use a knock out tool for the roof holes but this cost $135 at the local Lowes. I thought about just drilling, did this work ok for you and how big did you make the holes for the wiring?
  21. csarver

    shifter knob

    I finally got it off but cutting it off. I admit that, after getting the knob off, I found that the "just pull it method" wouldve worked if some jabrone hadnt permanently attached the knob to the stick with epoxy... Thanks for all the input guys.
  22. csarver

    Question AC Blower issue (I think)

    Sounds good fellas. I had replaced the blower motor this weekend (wasnt expensive and like Big Joe says, its easy to replace) this did nothing though, so I ordered a blower motor resistor for it. I havent put this on yet, but I will check out the evaporator coils and try the backwards shop vac...
  23. csarver

    shifter knob

    Yes sir, I twisted the 4x4 knob and it came off with a little effort. Then I really twisted the shifter knob and the rubber grip loosened and will spin (its still very snug, but I can spin it) but the cap piece that shows the shifting pattern stays put and does not move??? The stick holds to...
  24. csarver

    shifter knob

    I wanted to report on the "just pull real hard" method of getting the shifter knob off. DONT DO IT! I got the 4x4 shifter knob off like this but when I went to pull off the 5 speed shifter knob, I pulled and pulled and got nothing, so I reeeally pulled and the knob remained but the entire...
  25. csarver

    shifter knob

    Is this the same for the 4x4 shifter? I am leaving my 5 speed knob, but wanted to change my 4x4 shifter to a skull. Also, the one I was looking at simply comes with a rubber gromet inside of it, will this work at all or is it simply going to feel sloppy?

Members online

No members online now.
Total: 115 (members: 0, guests: 115)

Forum statistics

Threads
30,545
Messages
266,136
Members
14,673
Latest member
Doms350

Latest posts

Top