Search results

  1. arrowstrap

    rear hub/axle seals

    well they are WELL oiled. I'll jack it up and flow that oil. Thanks Crumm!
  2. arrowstrap

    rear hub/axle seals

    Bearings! So... it's the bath seal that needed replaceing. no big job... however, i forgot to grease the bearrings!!! i reused the old breaings and just wiped the 90W off to inspect them. do i need to pull them off again and grease the brearings? i'll prolly need new seals if i do.
  3. arrowstrap

    rear hub/axle seals

    yes axle seals. thanx for the tip! i hate re-doing work... i'll order from ford.
  4. arrowstrap

    rear hub/axle seals

    well it shouldnt be black magic or rocket science. i have a failing part and the failing part has a replacement part with a part number. i'd just like to know what that is so i can replace it, not buy every part and rebuild whatever fits in the rear end. i supose i can wait till i get home &...
  5. arrowstrap

    rear hub/axle seals

    hey, anyone know what seals i need to repair a 90w leak? i dont have my book with me & when i go to order the seals there are 2 kinds... TIMKEN Part # 9864S Seal; Rear Whl,Inner; Spicer 60, 61, 70 Ser. Axle BCA/NATIONAL Part # 370047A More Info {Oil Bath Seal} Rear Wheel; Inner im not sure...
  6. arrowstrap

    Glow plug relay voltage

    Tbar, my relay voltage stages are exactly as you discribed they should be. The old relay had a few rusted contacts. i have repaired these when replacing the relay. To my knowledge, the burnt wire is not exposing any wire. it apears the sheathing had heated once and it began to slide. i will...
  7. arrowstrap

    Glow plug relay voltage

    OK, i replaced the relay with the heavy duty allied... however when i key on there is still a VERY strong smell of burning plastic for a few minuites. any other ideas? currently i have the GPR harnes unplugged to keep the GP's from kicking on at all. i've no idea where to look from here...
  8. arrowstrap

    Beware of rock hammered tires

    so does anyone have any input on the tire size vs true mpg? i'm trying to weigh the initial and long term casts of the additional 3" of tire height.
  9. arrowstrap

    Best Lift Kit?

    So... if i pulled my current blocks and cut the required angle in them would that work? or am i better off just buying new blocks. i havnet been able to find angled blocks... think i'm looking in the wrong places.
  10. arrowstrap

    Best Lift Kit?

    I though i had the solid axle so i didn't need to do this alteration??? front axle is one peice tube steel going from L wheel to R wheel... correct me if i am wrong...?
  11. arrowstrap

    Best Lift Kit?

    I was not insinuating that the lift kits were trial and error systems designed and built by uncle bobs coat factory. I was looking for information on the cause and effect from someone who knows how these systems work. the sky site said it RECCOMENDS this and therefore means it is not a...
  12. arrowstrap

    Beware of rock hammered tires

    no one else drives the truck. no potholes here. i have 48000 miles on the tires. i guess my main consers is that this is ocurring to all four tires. i'd hate for this to ever happen again, so whatever i can to avoid this in the future...
  13. arrowstrap

    Best Lift Kit?

    i have a RSK + flip shackle to give me 5" front & 4.5" rear, sky recommends "no modifications are needed to correct pinion angle if only the flip kit is used. On long wheel base vehicles, using factory blocks, we recommend a 4 inch lift block with a 4 degree taper replace the factory blocks, in...
  14. arrowstrap

    Beware of rock hammered tires

    i have a set of BFgoodwrench tire on my truck. recently noticed a small bulge between the tread on the top of the wall. it continued to get worse. looks like a plug working its way out... then i looked at the rest of the tire. several similar bumps in an earlier stage... then i looked at the...
  15. arrowstrap

    Glow plug relay voltage

    Stroker, could you verify this is the right part? it looks as if the mount is in a diffrent location. does this GPR need to be mounted on it's side? thanks. Stancor / White-Rodgers - 586-902 - Allied Electronics
  16. arrowstrap

    Glow plug relay voltage

    ok, there are two sets of numbers on the relay, hopefully someone can match them up with a part! 183164601 0825M numbers are located on the housing. one set at numbers on each bolt bolt hole so i had to remove the bolts to view the entire number.
  17. arrowstrap

    Glow plug relay voltage

    I supose it is quiet possable that it is the wrong relay... i'll see if there are any part numbers on the unit and post my results. sure hope this is the fix!
  18. arrowstrap

    Glow plug relay voltage

    ok, so on the relay.... there are four terminal posts pertruding from the top. two are small and two are large. from the looks of the wire routing the two small posts and small wires are hot from the battery and the two large and going from the relay to the GP's. using a voltmeter while the GP's...
  19. arrowstrap

    Stock brake line length & fitting

    Yes, i am installing a 5" front 4.5" rear lift reverse and flip shackle kit.
  20. arrowstrap

    Glow plug relay voltage

    So, a few weeks ago i replaced my burnt valve cover harness, gasket and all the GP's. I can smell the harness burning again! I wonder if my relay is producing too much voltage to the plugs? what is the volt range of output for the relay? all my plugs are good and new motorcraft. any ideas on...
  21. arrowstrap

    Stock brake line length & fitting

    hey, i was wondering if anyone knows the stock brake line lengths and the fittings used? i am trying to get a quote for custom lines but i've no idea the stock length or the fittings, fitting sizes. 96 f350 4x4 crewcab Thanks!
  22. arrowstrap

    shock mount drop

    all the angles will remain aside from the amount the mount is sticking out from the truck. it will bring the shock in about 1.5" closer to the truck at the top. I'll look into superlifts mounts and see if they are basicly the same as if the stock were cut down.
  23. arrowstrap

    shock mount drop

    anyone see any issues with cutting a 4" section out of the front shock mounts and rewelding them as oppose to buying 5" lift shocks? the mounts are bolted on and it'd be pretty easy to cut them down.
  24. arrowstrap

    Random idle. Vacuum electric switch?

    so, i pulled a po236 code. boost pressure sensor. this issue occurs every time the truck starts regardless of the engine temp... however while pulling the codes i noticed that i left the chip programmed in PERF TOW mode. i reprogrammed it to PERFORMANCE and NOT not tow mode and the problem (so...
  25. arrowstrap

    Random idle. Vacuum electric switch?

    It is the map sensor. i looked up the part image and it's the same. so is my map sensor failing? hope not @ $150- $200 bucks for a replacement! my AC is turned off. With the engine running i can plug the hose in and create an erratic idle. as soon as i unplug it, the idle is fine...

Members online

Total: 285 (members: 1, guests: 284)

Forum statistics

Threads
30,545
Messages
266,136
Members
14,673
Latest member
Doms350

Latest posts

Top