Search results

  1. 2

    ambulance package ecm reflash

    I know that is what I should probally do but I just thought it would be nice to have 40 more on top of what the tuners would gain. I also kind of have a guy at the local dealer that might do it cheaper then the shop rate. I just wanted to know if anyone else has heard of this.
  2. 2

    ambulance package ecm reflash

    I was told by a guy at super chips today that there is a reflash the dealer can do to my truck to gain about 40 horse power. It is apparenty part of some EVAC package I guess. He also said the dealer could turn off the pilot injection to make possible to run single shots without a chip. I not...
  3. 2

    Making Smoke

    I am waiting to get a DP tuner until I put in new single shot injectors and a dual hpop system. I was just thinking of something to temporary to make it smoke off of an idle until I am able to upgrade injectors and oil pumps. I know of guys that put a resistor on the signal side of boost...
  4. 2

    Making Smoke

    To start off, I know that gobs of black smoke is wasteful, gives diesels a bad rap, and possibly harmful to the engine. I don't often do this, but I like to pull up beside cars with fart cannons on them and give them some diesel smoke to choke on. So onto my question, is it posible to fool the...
  5. 2

    Poor fuel mileage

    I pour in about 4oz of marvel mystery oil for every 10gal of diesel. Less then 2000 miles on a change of Shell 5w-40 synthetic, the pour milage didn't start with the oil. I get my fuel from a 1000 gal tank of road fuel at home here, it has 2% bio in it. I haven't seen any B20 pumps around...
  6. 2

    Poor fuel mileage

    My truck used to make about 18mpg in early spring and dropped to about 15mpg all summer long. It has new fuel filters on and I am pretty sure the fuel is good another truck is making about 20mpg. It seems to crank a liitle longer then it used to and it takes longer when the oil is warm. It...
  7. 2

    2000 p./s rough running

    mine did the same thing only 2 idm's, 1 pcm, 1 vc harness, and one new injector latter the problem was solved. If it isn't the vc harness I would do a injector buzz test and see if 8 is weak or not. If I would have put in a new injector in the first place, I would be a lot richer.
  8. 2

    P0284 trouble code

    Thanks for the help. I will try to figure something out to make sure that it is a bad injector. Thanks
  9. 2

    P0284 trouble code

    I thought an injector could be the problem, isn't number 8 supposed to be a long lead, I thought I read about that sometime. The wire from the computer out doesn't cause problems does it. Could make for an oppritunity for bigger injectors too. Thanks
  10. 2

    P0284 trouble code

    My truck has been having a slight miss on number 8 and doesn't set the check engine light. I did the cylinder contribution test and found the p0284 code. I bought a new VC harness and gasket and installed it on the left side, it helped for a couple days and then it was back. The international...
  11. 2

    P1316 code

    I pulled my truck into the shop to check the wires and connectors and found the problem. I unhooked the main engine harness turned it over and found the wire that fires Number 6 injector rubbed through. I seen where it was rubbing and shorting out on the valve cover. I taped up the wire and...
  12. 2

    P1316 code

    I should be able to use one Monday or Tuesday. The only thing is it seems to do it intermintinly. When I pull up to a stop light I can hear what sounds like a partial miss, but the truck doesn't shake like it is not firing at all and the CEL isn't on. Sometimes it runs just fine and lately...
  13. 2

    P1316 code

    How do you pull codes off the IDM? I am thinking it is probally a harness, but don't want to buy parts I don't need. 2 weeks ago the harnesses looked fine when I had the valve covers off. Thanks Gail
  14. 2

    P1316 code

    My truck showed this 3 times today. Once going to work and twice coming back. I think its someting to do with the Injector circut/IDM codes detected. But once I cleared it, it would run fine until the CEL would come on. Thanks in advance. Gail
  15. 2

    ICP

    Thanks for all the help. I'll do just that.
  16. 2

    ICP

    The code started about three months after I took the 10K mod out. Here are the numbers I got from driving it. ICP Idle Driving on Cruise at 60 Cruise at 65 WOT Volt .77-.89 1.26-1.44 1.40-1.61 2.96-3.35 Psi 467-492...
  17. 2

    ICP

    I will try to do that tomorrow sometime and report back later. I did notice a differance after installing the high pressure crossover that the pressures didn't spike high like they use to. Thanks
  18. 2

    ICP

    It would until I unpluged the sensor and then pluged it back in. Yeah I can get a Snap-on scaner. Just tell me when I need to read the values, I know the scaner can read psi and voltage. I just had it hooked up the other day, but I can't remember the exact readings. Thanks again.
  19. 2

    ICP

    The check engine light would come on when I turned the key on and then go off 2-5 minutes later when the truck was running. It never came on going down the road and it seemed to run fine. I did have the 10K mod on it and took it off but that has been 3 months ago. I did unhook the plug to see...
  20. 2

    ICP

    I pulled a P1280 code from my truck with my superchips tuner. It is something related to the icp. Any ideas? Is the sensor bad or is it something else. Thanks in advance.
  21. 2

    CPS shim set

    shim part # the International number is 1841521C91, but you have to have a speacial tool to check the current air gap. Most IH truck stores have one. the shims won't do you any good unless your CPS is off. if you want to learn more about it ask a service tech at an IH truck store.
  22. 2

    CPS shim set

    Has anyone else ever air gaped their CPS. While buying my new blue cps, the International parts guy asked if I wanted a shim kit. At first I stood there dumbfounded, then he pulled them out and said I would probally need them. I then responded by asking him what to set it to and he told me to...
  23. 2

    Loss of power

    Thanks for clearing up the dipstick numbers JOAT, I knew someone else must of heard about it too. I didn't see any soot on the firewall when I looked at it tonight and I don't think it has any air leaks. It could have a leaky manifold gasket, but I don't think it does. I did see the turbo...
  24. 2

    Loss of power

    I can assure you that the tube is not plugged, I cleaned it out earlier this year.
  25. 2

    Loss of power

    I knew what the codes ment but how do you find/fix the problem or test it, is what I would like to know. I will try to check lines, wires, and hoses tomorow. None of these codes ever made the CEL come on. Thanks for the help so far!!

Members online

Total: 224 (members: 2, guests: 222)

Forum statistics

Threads
30,555
Messages
266,193
Members
14,679
Latest member
Jriltex

Latest posts

Top