Search results

  1. K

    trucks not starting, keeps blowing the 30 amp gpr fuse

    i'll give it a shot this arfternoon. thanks pat
  2. K

    trucks not starting, keeps blowing the 30 amp gpr fuse

    i meant number 22 not 26
  3. K

    trucks not starting, keeps blowing the 30 amp gpr fuse

    bjs, i have number 26 on the underside of the cover, is this what you mean. thanks, joe
  4. K

    trucks not starting, keeps blowing the 30 amp gpr fuse

    i keep blowing the 30 amp gpr (glow plug relay) fuse. i have already tried disconnecting all 4 harnesses from the top of the valve covers, replaced the fuse, tried to start again and once again, POP goes the fuse. does anybody have any other ideas? where is my fuel heater? i hear thats on...
  5. K

    30 amp gp fuse keeps burning out

    thats even better thinking. thank you very much.
  6. K

    30 amp gp fuse keeps burning out

    figures, that was the only answer that i wasn't looking for. i need to bend some socket extensions just to get to that last valve cover bolt. (pass. side) thank you though.
  7. K

    30 amp gp fuse keeps burning out

    hey guys, i need help again. i think im looking for the right stuff again. my 30 amp gp fuse keeps burning out again and its too cold for her to get started. besides just looking at all 4 valve cover harnesses( for anything burnt), what else could i check or should i be looking for...
  8. K

    fuel mileage

    do you have any kind of a hissing sound, especially when you lightly take your foot off of the accelerator pedal?
  9. K

    i need a trans, can any one help

    hey guys, my buddy's trans is overheating and now its acting funny while shifting. he needs to shift his automatic trans into 1st in order to get it to start rolling, and so on. this is the fourth one that were looking for. 4r100 sounds familiar(i think that is what is in it now)...
  10. K

    96 clutch fan wrench size???

    thanks crumm, i appreciate it.
  11. K

    96 clutch fan wrench size???

    he guys, i need to know the exact size of the clutch fan nut that i need to remove the clutch fan from the water pump. i did the best i could using a tape measure to get the reading of 1 7/8". does anyone out there know if this is a definite? or should i be looking for something metric...
  12. K

    Shop Manual for 96 F-350 7.3PSD

    i picked up my haynes manual for the 96 ford f350 deisel from pep boys.(the pocal parts store around here like rs strauss, advance auto, napa)
  13. K

    starts and stalls 4 times in morning

    arrowstrap - i'll try that, that seems to be a good possibility. it runs rough with check engine light on when its cold only. got diesel - dieselpwrdredneck - the only way to check a cps is to replace it with a new one right? action4478 - whats the ipr and how is it checked and where's...
  14. K

    starts and stalls 4 times in morning

    hillbilly - i could be letting it warm up a little better, but even though, stalling is not normal when i'm on the interstate already (warmed up). gotdeisel - temp outside in the morning is 27 degrees farenheight. fuel filter was changed 1 week and 2 days ago (made sure that was tight). i...
  15. K

    starts and stalls 4 times in morning

    the past 3 days the temperature outside has dropped considerably. 1. i don't plug the truck in at night yet. 2. i start the truck and it runs rough to my first stall. 3. i get it going again, then attempt to drive, 100 feet away, i stall. 4. starts again, start driving, it bucks and...
  16. K

    tire rub

    i don't know what the specs are on the on the 8x?. but dont forget that when you go from stock to larger tires that you need to adjust the turn stops. its a bolt that you need to loosen and tighten the nut stop at the same time. yours should also be located just under the calipers on both the...
  17. K

    infamous oil leak at the dipstick

    there's an o-ring on the inside of the oil pan side and rtv blue goes on the outside where you tighten it. the only to replace it is by pulling the oil pan and then pulling the motor. that's what i just did.
  18. K

    What do ya think

    go to kbb.com , do both trade-in value and private party value and judge somewhere in that range.
  19. K

    metal brake line has rusted through

    that was what i was thinking. thanks dave.
  20. K

    metal brake line has rusted through

    ok, now that the motor is back in the truck and i have test driven it, i noticed that i have a new leak. it comes from where the metal line meets the rubber line on the front passenger side. i could see exactly where it is leaking from. the question is... does anyone know if ford, pep...
  21. K

    i have an oil leak and need help

    ok fellas, as it turns out, i used "PERMATEX 2B" form a gasket stuff. i put it on friday the 13th and let the motor sit for a few days before even getting started on the re-installation. thursday the 19th, i got it back together enough to start the motor and let it run for a little bit(15...
  22. K

    Odd Clutch Problem

    these are the photos of my dual flywheel. in the first picture you could see the space between the 2 flywheels. there is about 1/2 inch play between them.
  23. K

    i have an oil leak and need help

    Does anyone know if it is okay to start the engine without the transmission installed? I will have both fly wheels and clutch assembly installed. Thanks- Joe
  24. K

    what kind of mileage to expect

    that's what i thought too. 1 place said 8 and 2 others said 6 or more. i thought that was impossible and way too unaffordable.
  25. K

    turbo surge?

    how's your fuel milage. did you notice a lower mpg like i did. it's a hissing sound out of your exhaust right? does it do it a few times on idle when you first start the truck?

Members online

Total: 76 (members: 1, guests: 75)

Forum statistics

Threads
30,545
Messages
266,137
Members
14,673
Latest member
Doms350

Latest posts

Top