Search results

  1. cstewart

    another project gone bad

    hey daveben are u sayin that i should not have been able to pull the axle out of the housing through the spindle with the hub off? ive been thinkin about what u said and im not sure i understand. and yes that large expensive seal is toast lol i think i found it somewhere for like $80 maybe . ...
  2. cstewart

    another project gone bad

    sorry shouldve explained better i had the whole hub off the truck with the axle still in it and couldnt get the axle out of it.
  3. cstewart

    another project gone bad

    not sure what had happened but it was just wedged in there probably from all the mud and sand but i got it out now so its good to go . . thanks
  4. cstewart

    another project gone bad

    my left front hub has been making some horrible noises and grinding real bad here the past few days and my four wheel drive didnt work so i just automatically assumed it was the locking hub.i pulled it all apart this morning but when i pulled the hub assembly off the axle came out with it, ive...
  5. cstewart

    Help Needed No brakes!!!

    yeah lesson definatly learned. . not making that mistake again
  6. cstewart

    Help Needed No brakes!!!

    alright so it drew my last bit of patience and i figured at last i would just replace the pump again, hoping that i got a bad one and that would fix the problem. . yep that was it. im really glad i fixed it but pissed at the same time cause it was something so small like that, thanks for the...
  7. cstewart

    Help Needed No brakes!!!

    no but if u explain to me the procedures to use one i will go get one
  8. cstewart

    Help Needed No brakes!!!

    well after pumpin the brakes alot it did help a little. the brake used to be as hard as a rock but now it gives a little. . . while holding the brake it goes down so far but if u rev up the engine the brake pedal will go closer to the floor. (hope that'll help diagnose)and the power steering...
  9. cstewart

    Help Needed No brakes!!!

    the fluid looks good, i jacked it up and turned the wheel lock to lock for over an hour, i even held it at like 1500 rpm while turning the wheel which got alot of air out. the other day when rpm's were higher the power steering and brakes would sort of work now it seems like that doesnt have the...
  10. cstewart

    hey i read a post where u commented that u can get the air out of the powersteering system using...

    hey i read a post where u commented that u can get the air out of the powersteering system using a vacuum pump can u explain that to me cause i am not sure that i understand
  11. cstewart

    Help Needed No brakes!!!

    :dunnook so i got the pump replaced and bled the system. . drove it for less than a mile. no power steering no brakes. bled the system again and took alot of air out but still the same thing.any ideas of what it could be now?
  12. cstewart

    Help Needed No brakes!!!

    :doh:yeah it was definatly and experience then i had to drive it like 20 mins down the highway back home cause i had no other way to get it there. downshifting to slow down and hopin for the best lol. lesson definatly learned
  13. cstewart

    Help Needed No brakes!!!

    sorry guys im not so technology savvy so stuff like that gets complicated lol. . well its is a 2000 f350 with the 7.3. i took off the power steering pump and there is alot of play in it like the pulley moves alot. . b4 i took it off though as long as i kept the rpms up it would work fine so im...
  14. cstewart

    oh ok got ya. . no its a 2000 model.

    oh ok got ya. . no its a 2000 model.
  15. cstewart

    Help Needed No brakes!!!

    so i checked it all out and the pump has got to be toasted cause nothin else seems to be wrong. . guess im on my way to auto zone lol
  16. cstewart

    Help Needed No brakes!!!

    SO we were playin in the mud and when we were leavin as i was pullin onto the road i noticed i had no power steering. . when i went to slow down to make the turn, no brakes!!! any help at all would be appreciated . .i looked and there doesnt appear to be any lines disconnected or major leaks :dunno

Members online

No members online now.

Forum statistics

Threads
30,557
Messages
266,196
Members
14,680
Latest member
Jriltex
Top